Custom Metal Flashing & Trim Fabrication in Dallas-Fort Worth
Send a Drawing
Quick Turnaround
Color Matched
Built to Your Detail
Roofs and walls leak at the transitions, not in the middle of the panel. Flashing and trim keep water out at eaves, rakes, ridges, valleys, parapets and wall intersections. We bend every piece to your dimensions on the shears and brakes in our Richland Hills shop.
Bent to your drawing
A sketch, a detail or a cut list. We bend to it.
Matched to your panels
Same coil and color as your roof or walls.
24 to 29 gauge
Steel and aluminum; stainless and copper by order.
Pickup or delivery
From Richland Hills, across Dallas-Fort Worth.
Flashing and Trim Profiles We Fabricate
These are the pieces we make most. If yours is not listed, we can still make it: anything that can be sheared and bent from flat sheet. Standard lengths are 10 feet, and most profiles can go longer up to our brake length. Hems, kick-outs and closed ends are available on request.
Drip edge and eave trim
Rake and gable trim
Ridge cap
Valley flashing
Step and counter flashing
Parapet coping
See all 14 profiles we fabricate
| Profile | Where it goes | Typical sizes | Notes |
|---|---|---|---|
| Drip edge / eave trim | Bottom edge of the roof, over the fascia | 2" to 4" face, 10' lengths | Hemmed edge for standing seam eave clips |
| Rake / gable trim | Sloped edges of a gable roof | 3" to 6" face | Matched to panel profile; Z-closure available |
| Ridge cap | Peak of the roof | 12" to 20" girth, vented or solid | Sized to panel rib height; foam or metal closures |
| Hip cap | External hip lines | Matches ridge | Pre-cut miters on request |
| Valley flashing | Internal roof intersections | 16" to 24" wide, W or V profile | 24 ga recommended; hemmed edges for cleat |
| Step / counter flashing | Chimneys, side walls, parapets | Custom | Reglet or surface-mount; sealant-ready hem |
| Headwall / apron flashing | Where a roof meets a vertical wall above it | Custom girth | Z-closure under the hem |
| Sidewall flashing | Where a roof meets a wall on its side | Custom | Matched to panel rib for a tight fit |
| Parapet coping | Top of commercial parapet walls | 12" to 30" girth, cleat or clip-mounted | ANSI/SPRI ES-1 style details available |
| Z, J and L trim | Panel terminations, closures, around openings | Any leg length | Bulk pricing for metal buildings |
| Corner trim (inside / outside) | Wall panel corners | 3" to 6" legs | Matched to board and batten or R-panel |
| Framed-opening and base trim | Doors, windows, slab line on metal buildings | Per building | Sold as part of a trim package |
| Chimney caps, pitch pans, boots | Penetrations | Custom | Welded or sealed seams; stainless available |
| Gutters and downspouts | Roof edge drainage | 5" and 6" K-style, box gutter; 2x3, 3x4 downspouts | Seamless gutter run to length |
Have a drawing? Get a price today.
Send a sketch, a detail or a cut list with the material, gauge and color.
Materials, Gauges and Finishes
Painted Galvalume steel
- 24, 26 and 29 gauge
- Berridge PVDF (Kynar 500) colors
- Matches standing seam, R-panel and board and batten
Aluminum
- .032 and .040 in.
- Painted or mill finish
- Coastal or chemical sites, light coping, gutters
Stainless and copper
- Special order
- Chimney caps and exposed details
- Historic and high-end homes
Matching your panels
When trim is bent from the same coil as the roof or wall panels, the color and gloss match exactly and age the same way. Bought your panels from us? We pull trim from the same coil. Panels from another supplier? Bring a sample and we will match it to the nearest Berridge color, or order a custom coil for larger jobs.
Equipment
Our shop runs shears and folding brakes alongside our New Tech Machinery panel lines, so your trim is cut and bent in the same shop that forms your panels.
See all materials, gauges and finishes
| Material | Gauges we stock | Finish options | Use it for |
|---|---|---|---|
| Painted Galvalume steel | 24, 26, 29 ga | Berridge PVDF (Kynar 500) colors, SMP on request | Trim matched to standing seam, R-panel and board and batten |
| Bare Galvalume | 24, 26 ga | Mill finish | Underlayment flashing, barns, budget trim |
| Galvanized steel (G90) | 24, 26 ga | Mill or paint-grip | Valley, step and counter flashing under shingles and tile |
| Aluminum | .032", .040" | Painted or mill | Coastal or chemical environments, lightweight coping, gutters |
| Stainless steel | 26 ga, 24 ga (special order) | 2B or #4 | Chimney caps, caustic environments, exposed architectural details |
| Copper | 16 oz (special order) | Natural | Historic and high-end residential detailing |
How to Order Flashing and Trim
Send the profile
A sketch with sizes and bend angles, a detail, a photo or a cut list.
Pick the metal
Material, gauge, color and quantity. Matching our panels? Give us the order number.
Approve the quote
By the piece or per linear foot. Standard trim ships in days.
Pick up or delivery
Trim rides fine in a pickup; big orders go on our flatbed with your panels.
Minimums and how trim is priced
There is no minimum for standard trim pieces. Custom profiles carry a short setup charge that goes away at volume. Trim is priced by its girth (how much metal is in the piece) and the number of bends, so coping and large pieces cost more than simple trim. Send us your profile drawing, or a photo with measurements, and we will quote by the piece or per foot.
Worked example: trim package for a 30x40 shop
| Piece | Qty | Why |
|---|---|---|
| Ridge cap, 10' | 4 | 40' ridge |
| Eave trim, 10' | 8 | Two 40' eaves |
| Rake trim, 10' | 8 | Four 16' rakes + waste |
| Outside corner, 10' | 6 | Four 14' corners |
| Base trim, 10' | 14 | 140' perimeter |
| Framed-opening trim | 1 set | One 12x12 overhead door, one walk door, two windows |
| Closures and screws | 1 kit | Foam closures at eave and ridge |
Order the trim with your panels and it all arrives in one color, in one delivery.
Flashing and Trim Service Area
Pickup in about 20 minutes
Our shop at 2333 Delante in Fort Worth is close to North Richland Hills, Haltom City, Hurst, Bedford, Euless, Keller, Watauga, Colleyville and Grapevine.
Delivery across DFW and Austin
We deliver across the Metroplex, including Arlington, Grand Prairie, Mansfield, Burleson, Weatherford, Denton, Dallas, Irving and Plano, and serve the Austin area from 7620 Guadalupe Street.
Most of our trim goes to roofing contractors, metal-building crews and remodelers, but we sell to homeowners too. Need one piece of counter flashing bent right to fix a leak? We will make it.
Frequently Asked Questions
Still have a question? Call us at (817) 682-6977 or send your drawing or plans.
How much does custom metal flashing cost?
It depends on the girth (how much metal is in the piece), the number of bends, the gauge and the material. Coping, wide valley flashing and stainless or copper pieces cost more than standard 24 gauge painted trim. Titan quotes by the piece or per foot from your drawing, so send us a sketch with dimensions or call (817) 682-6977 for a price.
What gauge should roof flashing be?
24 gauge is the standard for valley, step, counter and eave flashing on metal roofs and on commercial work because it is stiff and resists hail. 26 gauge is common on residential shingle roofs and metal-building trim. 29 gauge is a budget option for low-exposure trim. Match the trim gauge to the panel gauge whenever possible.
Can you fabricate flashing from my drawing?
Yes. Send a dimensioned sketch, an architectural detail or a photo of the existing piece. We confirm the bend angles and girth back to you before fabricating.
How fast can I get flashing in Fort Worth?
Standard trim profiles in stock colors are typically ready within a few business days, and small emergency pieces can often be bent while you wait. Custom profiles, custom colors and special-order metals take longer. Call (817) 682-6977 with your deadline and we will tell you what is possible.
Can you match the color of my roof or siding panels?
Yes. We stock the Berridge color line and bend trim from the same coil as our panels. For panels from another manufacturer, bring a sample and we will match to the nearest stock color or order a custom-painted coil for larger quantities.
Do you make seamless gutters?
Yes. We fabricate seamless K-style and box gutters run to length, with matching downspouts, in the same colors as our roofing and trim.
What is the difference between step flashing and counter flashing?
Step flashing is a series of L-shaped pieces woven into the roofing courses where a roof meets a wall. Counter flashing is the piece that laps over the top of the step flashing and is set into or against the wall so water running down the wall cannot get behind the step flashing. Both are needed at chimneys and side walls.
Related Services
Standing Seam Panels
Berridge Tee-Lock, Cee-Lock and Zee-Lock panels roll-formed to length at our shop or on your site.
Soffit
Vented and solid metal soffit panels that finish the eave and match your trim.
Metal Accents
Spires, Juliet awnings, chimney caps and decorative metal that finish a project.
Have a drawing or a cut list?
Send it over and we will quote it by the piece or per foot. Upload it on the quote form or email sales@titansheetmetal.com.
Call (817) 682-6977